Annamalai University M.Sc I.T 2k4-2k9
Welcome To AUMSCIT ForuM.
Our Farewell Day Photos are present @ Announcement Section.


This Forum will act as a bridge to connect students of M.Sc I.T 2004-2009 batch belongs to Annamalai University, TN, India
 
HomeGalleryFAQSearchMemberlistUsergroupsRegisterLog in
Hi, our Farewell Day Celebration Photos are available @ Announcement Section

Share | 
 

 Some Interview Question: CCNA & Basic Networking

Go down 
AuthorMessage
arunkumar

avatar

Male
Number of posts : 209
Age : 32
Location : CDM,IndiA
Job/hobbies : Till now Student
Registration date : 2008-10-21

PostSubject: Some Interview Question: CCNA & Basic Networking   Sun May 03, 2009 9:46 pm

Some Interview Question: CCNA & Basic Networking

Basics Q & A {Switching}

1) What is unicast and how does it work?

** Unicast is a one-to-one transmission method. A single frame is sent from the source to a destination on a network. When this frame is received by the switch, the frame is sent on to the network, and the network passes the frame to its destination from the source to a specific destination on a network.

2) What is multicast and how does it work?

** Multicast is a one-to-many transmission method. A single frame is sent from the source to multiple destinations on a network using a multicast address. When this frame is received by the switch, the frame is sent on to the network and the network passes the frame to its intended destination group.

3: What is broadcast and how does it work?

** Broadcast is a one-to-all transmission method. A single frame is sent from the source to a destination on a network using a multicast address. When this frame is received by the switch, the frame is sent on to the network. The network passes the frame to all nodes in the destination network from the source to an unknown destination on a network using a broadcast address. When the switch receives this frame, the frame is sent on to all the networks, and the networks pass the frame on to all the nodes. If it reaches a router, the broadcast frame is dropped.

4: What is fragmentation?

** Fragmentation in a network is the breaking down of a data packet into smaller pieces to accommodate the maximum transmission unit (MTU) of the network.

5:What is MTU? What's the MTU for traditional Ethernet?

** MTU is the acronym for maximum transmission unit and is the largest frame size that can be transmitted over a network. Messages longer than the MTU must be divided into smaller frames. The network layer (Layer 3) protocol determines the MTU from the data link layer (Layer 2) protocol and fragments the messages into the appropriate frame size, making the frames available to the lower layer for transmission without further fragmentation. The MTU for Ethernet is 1518 bytes.

6: What is a MAC address?

** A MAC address is the physical address of a network device and is 48 bits (6 bytes) long. MAC addresses are also known as physical addresses or hardware addresses.

7) What is the difference between a runt and a giant, specific to traditional Ethernet?

** In Ethernet a runt is a frame that is less than 64 bytes in length, and a giant is a frame that is greater than 1518 bytes in length. Giants are frames that are greater than the MTU used, which might not always be 1518 bytes.

8: What is the difference between store-and-forward and cut-through switching?

** Cut-through switching examines just the frame header, determining the output switch port through which the frame will be forwarded. Store-and-forward examines the entire frame, header and data payload, for errors. If the frame is error free, it is forwarded out its destination switch port interface. If the frame has errors, the switch drops the frame from its buffers. This is also known as discarding the frame to the bit bucket.

9: What is the difference between Layer 2 switching and Layer 3 switching?

* * Layer 2 switches make their forwarding decisions based on the Layer 2 (data link) address, such as the MAC address. Layer 3 switches make their forwarding decisions based on the Layer 3 (network) address.

10: What is the difference between Layer 3 switching and routing?

** The difference between Layer 3 switching and routing is that Layer 3 switches have hardware to pass data traffic as fast as Layer 2 switches. However, Layer 3 switches make decisions regarding how to transmit traffic at Layer 3 in the same way as a router. A Layer 3 switch cannot use WAN circuits or use routing protocols; a router is still required for these functions
Back to top Go down
View user profile http://cybersak.blogspot.com
 
Some Interview Question: CCNA & Basic Networking
Back to top 
Page 1 of 1
 Similar topics
-
» Selenium Interview Questions
» What are the basic requirements for using Selenium IDE?
» HSP Radio Podcast Interview with Elaine Aron
» Interview: Archan Nair
» amaralĀ“s interview at TV Portuguese channel

Permissions in this forum:You cannot reply to topics in this forum
Annamalai University M.Sc I.T 2k4-2k9 :: Noticeboard :: Career Tips & Suggestion-
Jump to: